■This is a rear carrier with a designed aluminum top plate. ■Because it is a product exclusive for each model, the form of the vehicle body is comfortable even when it is not loaded with luggage.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
It's very solidly made and I'm very happy with it. But it is a pity that Cushion that fills the gap of Seat.:I think you set it! I bought some Daruma-shaped packing at home center and attached it. I think it looks good too!View Detail
Installed on a Ninja250R Unfortunately, there's no other choice for a used 10 year old Ninja Parenthesis is good, but needs some Gold processing on the Motorcycle side It's going to be bulky from the NORMAL Tandem seat Even with the included Sponge, there is still a space between the Seat Cowl and Tandem seat There will be a gap of about 1cmView Detail
I installed it in my friend Ninja 250R 2011. In 2011 we need to cut the Lock holder's Plate by about 4 mm, but because I owned the Ninja 250 R 2009 Formula, Holder's Plate was replaced with my Ninja's one so there was no need to cut it. Fixing the carrier to the car body is a way to fix it to the car body with a nut through the hole from the top through the hole which is vacant from the beginning of the frame from underneath. The nut and locknut from below are used and it is impossible to stop until the carrier can be temporarily attached with your fingers. Therefore, while holding down the carrier so that it does not slip, it is necessary to hold the nut down with a wrench so that it does not come around and work to tighten the nut on the top is necessary, so I think it is a pain to do alone. It is necessary to remove the wrench that prevents the rotation of the nut, unless the nut fixing the front, the on-board tool and the plastic cover fixing it are not removed. It is easier to push the front nut against the frame from the near side and align it with the bolt hole while sliding it, then bolt from the top. If you first pass the bolt and try to attach the nut to it, there is no space and it is hard work. It is a hex Bolt of fixed Bolt, M6 in front, but if you put your strength in Ratchet and tighten it, it will be twisted. My friend tightened this time, but I got screwed. Fortunately there was M6 Bolt on hand so I came up with it. There is a gap between Seat and Rear cowl as much as Carrier's Bracket passes. Sponge's mall is attached to fill it, but I can not do this. I wear a mall on the Seat side, but I can see the mall from the outside and it looks bad.
Also, after installing the Carrier, I attached the Box of GIVI, but indeed the same selling agency has a hole from the beginning in the position where GIVI 's Mono - lock base can fit snugly.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!