[Specification] ・Rated voltage: DC12V ・Outer diameter dimension: W25.5mm x H30.5mm x D15.5mm (*excluding protruding parts)
[Components] ・SPI-110 C1 main unit x 1 ・Model Specific Harness x 1 ・Various double-sided tapes ・Instruction manual *Components vary by kit.
*When the clutch is depressed while driving, the display shows a gear other than the one in which the clutch is engaged, but this is not a malfunction. *Prioritize safety while driving and do not be careless in front.
*Please do not use non-resistive spark plugs.If you use a plug without resistance, noise may be generated and the rotation signal may not be input correctly, so please use a spark plug with resistance. *Please put the attached double-sided tape on the back side of this product to prevent water from entering because there is a switch. *Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage. *After installing this product, periodically inspect it to see if any parts have fallen off. *PROTEC is not responsible for any damage or accident caused by the use of this product. *Protec is not responsible for any labor charges for removal or other expenses incurred during repair. *All vehicles that have been tested by Protec are stock.There is a possibility that a problem may occur if the vehicle is equipped with aftermarket parts other than stock parts. *Please refer to the service manual of your motorcycle to confirm the respective wiring before installation.
●All the necessary parts are included in this kit!Easy installation with special harness! It can be installed easily without soldering because it uses a special harness for each model. *The vehicle-specific harness has a 12V (+) service terminal for easy installation of the CS-550 burglar alarm.
●Compact design! The main unit dimensions are W25.5mm X H30.5mm X D15.5mm (excluding protruding parts), a compact design that does not interfere with installation around the meter.
●LED display for high visibility! Equipped with a dimmer sensor [automatic dimming function].The brightness of the LED is automatically adjusted to be brighter in the daytime and darker at night to improve the visibility of the digital numerals.
●Equipped with a shift up indicator! Since the rpm can be set arbitrarily, it can be used for everything from narrowing to preventing over-revving.The blue LED will light up when the rotation is higher than the set value. *You can re-register as many times as you like.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
After about three days Hmm? It's dark The display is clearly darker than I thought it would be It was dark enough to be visible at night I tried to install it again, but it didn't work, so I'm using it as it is
I haven't done anything with the settings or anything else, can I fix it with some kind of manipulation?View Detail
After buying Motorcycle, put in 7th gear from around 3000 km after break-in (Do not fit) Purchased for frequent occurrences. For everyday use on a city ride Main, I think that there is a difference between Large. (Example : It is released from the Stress which makes a morning swing by the situation that it is now 5th speed? 6th speed? However, when you get used to it, you will almost stop seeing and sometimes regret not to watch seven gears for watching w
Although it is a good Parts that may or may not be present, it is surprisingly useful for town riding Main. People who do not need this "People who can always grasp how many speeds are perfect now" Or "People who can grasp how many speeds instantly with speed and speed" I think. It will be a standard for the 18 year style Parts.
About installation It was supposed to be able to attach, but the dedicated Coupler was disconnected and the Meter reaction was bad. (Occasionally disappear) We had to exchange at Manufacturer, but the situation has not changed. Because it seemed that Body side Connector was the cause (No problem when restored) I gave up the dedicated Coupler, made my own Coupler, and made it interrupt..
I do not know what is there so I thought that it would be better to ask Shop for installation.View Detail
Owned Motorcycle is RoseRose at 4th speed of old car, 5th speed of off car, 6th speed of NINJA. As expected, the 6th gear of CROSS Gimi is occasionally occupied by the Smooth of the current Engine "Are you ??" It was often that. As for installation, Cowl removal is still Large work. It is certain that you can record several types of Screw and Clamp while recording with Digital camera. If you unintentionally remove Light and including it, you can not force unnecessary power on Wiring and Connector. Also, it's easy to finish vibration proof with Tie Wrap after installation. My ingenuity is behind Meter "ConnectorWaterproof Cover" Cut from the thinner to Limit where Connector passes through, remove it, wound with Vinyl Tape for electric machinery and reused it. Accessory "WaterproofSeal" Covered the interconnected Connector part with seaweed windings and made it Completely Waterproof. As Waterproof thinks that this will never be removed again this person is sure. Display while driving is delayed by one TEMPO 13 at the time of Downshift, but there is no particular inconvenience. It seems that one trouble has disappeared (Lol) It is comfortable.View Detail
My Ninja 250 is in a bad condition of GEAR and there are times when GEAR is missing when you enter the acceleration state when SHIFT UP to 4th speed 5th speed 6th speed, 1st speed Downshift, can not do SHIFT UP. There was a case that I could not understand what speed it was in such a case, I was in trouble. Attaching Shift positionIndicator seemed like a beginner, but there was resistance, but I thought that I had no choice but to rely on this anymore. Impressions attached do not have to check whether it is in the 6th speed, but even if GEAR's condition is bad, I will be saved because it displays the current Shift position. With Shift Up Indicator, Blue's Lamp will tell you even when you can not afford to see the Tachometer. Although it is not necessary to say that it is not necessary, I think that it is a convenient Items. Although it is installation work, it is Kit special kit so it is very easy! Remove the Coupler stuck in the back of the Meter and just insert a special Wiring between the Coupler and Meter. However, working efficiency is better if you remove all previous Cowl from Side cover and make it naked, but that is surprisingly troublesome. Although it is a mounting position, thought that Right near Tachometer's Upshift point is easier to see, I made Bracket and installed it. At first there was resistance but I think that I was really wearing it.View Detail
It has attached to Ninja250.Since there is a Kit only for a vehicle type, it is overly easy work [ only inserting between the Connector of a Meter flesh side and a Main harness ].Even if it does not remove the Front cowl, it can do somehow, but the way removed since it adjusted regards management of wiring of the removed way etc. as good as a result.
Although it is an important effect, it becomes [ May not I be as a Title? ] and is a place.Although it was a little late for the Timing of a Shift change, it seldom became mind.The circumference of a Meter thinks of itself to the grade which became busy (smile). View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!