[How is it used? I bought this for my CYGNUS X SR Model 5 Oilfor Replacement, and the CYGNUS has an exquisite Center Stand in the way. I bought this product because there is a drain bolt and the Center Stand is too low to fit a large-geometry oil pan.
Was the one you received as per Image? It's a great product, but I'm not sure if it's the right size for me. I thought it would be no problem if I could cover the cost. The size is just right for implementation and is easy to use.
How was your experience with it? It is simple and easy to use. I also use it to change the oil in the circuit of my YZF-R25, which has been converted to a racer. The only problem is that the sink is still flat, so there is a high possibility of spilling on the Large when you throw it away. So I'm thinking of either cutting it or intentionally hitting the exhaust pipe to melt it and make it easier to flow.
[Points to note] As others have mentioned, be careful when you pass the Center Stand through the neck, if it doesn't go in at an angle! It's fine when you put it in, but after you pull the oil out, you have to angle it to get it out! Then it's a large disaster (laughs). If the amount you pull out is small, you can go without spilling, but if it's a lot, you will definitely spill.
How did it compare to other products? I think the square oil pan has a merit that it can be stacked. If you are using a scooter, the Center Stand will be in the way. That makes me wonder if it's any other shape than this one!View Detail
I bought it for Oilfor Replacement of YAMAHA SR 400. Oil of SR is Dry scattering type, so when removing Oil, Main is pulled out from Oil drain of Front Frame, but Oil remaining in Oil pan needs to be pulled out as well. However, when setting up the Center Stand and accessing the Oil drain bolt, the installation is sideways, and because of the positional relationship with Center Stand, I felt it was difficult to use it with a general circular object.
So I purchased this PROTOOLS Compact Oil Drain Pan! It was introduced as Scooter and Small Type for Vehicle, but the capacity is 2. With 68 L, Oil Capacity 2 of SR 400. It was decided that it was enough for 1 L. Size is also Exactly, it fits in the gap of Center Stand, and it seems to be active in the future Oil replacement work.
Actual size is outside, height 40 cm, side 23 cm, height 7. 5cm. The inside is a deep place where Oil gathers, there are 14 cm in length, 20 cm in width, and 6 cm in depth. The narrow part that catches the Oil of the tip part is the widest part on the outside is 17 cm and the narrow part is 15 cm. Besides that, in the inside of a place with grooves vertically, it has a slope of 16 cm in length, 20 cm in width and 13 cm in width.. The feeling put on the floor has a sense of stability and it is very reliable!
Well, it is said that Large doubles as Small, but again "Appropriate material right place, proper use" It is necessary. Since this time PROTOOLS Compact Oil Drain Pan is newly added, it seems to be able to enjoy Oil replacement work efficiently. In the photograph, the PROTOOLS Sticker is stuck, but I tried to peel off what was attached to the packed bag.View Detail
I bought it to Oilfor Replacement of SUPER CUB 90. It is good in shape that is easy to use in shape with Compact as Large tincture. It is even better if the price is a bit cheaper.View Detail
He wanted the small suspended tray used at a Garage, and it purchased about three.as
Oil Drip pan -- the capacity 2L -- since it is a few, does a just right work load receive the Engine oil of small displacement volume vehicles, such as an about [ 0.5L~1L ] Fork oil, a Gear oil, and Cub, at most?Since
BMW K1200RS has a Drain of a Transmission per Pivot of a Center stand.Although the catchphrase which can let between the Center stands of a Scooter pass was expected and he bought it with eye aim -- It was a disappointment for a while in the state where an Oil will fall if the portion which the end extracted twists by an Exactly at the gap of a Center stand and it will twist when [ at which it puts and puts ] = Removing.
In fact, the direction of uses other than an Oil Drip pan is user-friendly.As for the portion which the end extracted, a crevice is made between the floors which are raised bottoms and were placed, and since it is good for holding by hand exactly, it is used conveniently to carry out every [ of the tool in use / temporary ] by the floor of a Garage, or once receive dirt parts.The imitation is put on the market also from the > DAYTONA, and on a nominal-cost Base, since it is practically equal, I think whether stock, a Sale discount rate, etc. are seen and the more suitable one should just be chosen.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!