PMC(Performance Motorcycle Creative) has a lineup of parts essential to restoration such as KAWASAKI Z & Triple series, reproduction parts of discontinued products for vintage motorcycle and OEM and customization type turn signal & tail lamp
 |  |  |
| | | |
 |  |  |
| | | |
 |  |  |
| | | |
 | ||
| |
I was worried about 45φ but when I put it on, I thought it was the right size.Bracket and bulbs are sold separately and are Socket for Single Bulb.I use Front as a replacement for my WSocket.Plating p...
I changed the Swing Arm to Other Brand Product the other day, so I installed the Guide roller to avoid interference with the Chain.The shop where I installed this car said that the installation accura...
I've always thought that I couldn't miss the wheel replacement on my 80's Super BIKE Custom, and although there were many options, I chose PMCSORD/Heritage.I just chose Rear first for the Rim width an...
Used with Offset50mm ZapperStem.The wire length is 64.5cm of Standard. 69.5cm of Long Type is also available.Grease is applied to the wire from the beginning.
I appreciate that the OEM missing Parts is a Ripro product.The installation is almost the same as the OEM product. I would like to thank the manufacturer for selling these parts as well.
Unlike paper, it's not likely to stick, and even if it does, it's not a problem to clean up, so I think it's possible.However, the accuracy of Cutline is not so high, so you need to be careful.It's no...
To be honest, it's cheesy, as it's a plastic evaporated plating? finish.However, there are some motorcycles that don't stripe without an Emblem on the Front, so in that case I'd have to add one.If the...
Since the Pad pin that comes with the CP2696 Caliper is like the Split Pin, I bought the Quick release pad pin without having to install the Caliper.If you're going to be doing frequent Maintenance, t...
STDSpoke, STDCasting, DYMAG for MK2, SWORD, Morris, etc., are all available in kits for each Wheel, so you can install them completely Bolt On.The Inner rotor is available in Silver or Black.Since it'...
The four hole positions on the screen stay were different.I installed a carbon cover, though, so I could fool you.It was off by more than two centimeters.Isn't the wrong hole location a problem for th...
 |  | |
| | |
Sold separately for some reasonMaybe it's the Rubber quality of PMC's Indicator, but it's so lurid that it goes around and around when you put it on It is not easy to work with due to the need to inst...
Since TMR 36 is used in Z1, PMC's Indicator and Quantity : Purchased for use with Set.Since it was the same thing as originally attached, I selected it without hesitation, but this Band seemed to ...
Insulator band is not a good thing if tightened tightly. However,. When replacing Insulator Screw Mountain is sorely exchanged together without exception. It is a cheap consumable item. There is no se...
Refresh according to Harness exchange of Z750FX3 !!We processed Wiring and moved it under the Battery case at the position where Regulator was located in OEM.I pray for a long time.
Die length is just going to be several more millimeters.
a feeling -- short kana.
If there are brand-name parts, does he recommend there?...
Since the relay of the cell broke down, it exchanged for here instead of an original manufacturer's product. A result does not change mostly that it is pure, although it can use ordinarily. It is only...
 | ||
| |
I help my friend to buy it. It seems as universal for most of the motorbike. My friend use it on YS250 and fit for it. The texture of this lock is hard. Seems not to bad. My friend use it very success...
I helped my friend to bought it. I am using the Japan brand kitaco but however that is not fit to my friend motorbike, so I bought this because it is universal one. It is made in Taiwan, so I think it...
Since the Helmet lock of the KSR which I am on now is in a place where it is very hard to use, I bought this Universal Product here.Although I was satisfied with the functional aspect, it was better n...
Thank you for supplying finer parts of old car.Although it may be Refreshing if it does not have an appearance, I think that it is a handy part if there is.The shape is also faithful? Do not touch the...
Large size did not fit a little with CB 400 SB, but if you tighten it tightly you will not loosen and you can set the mounting position freely and Helmet lock is easy.
Busy at VERSYS of Kawasaki.Helium hook attached to the car from the beginning must bother to use Seat unless it is inconvenient because it can not be used,I had this installed before car delivery.When...
PCX does not have Combination Nifrek. Seat is also narrow. I use it for Combination Nifrek for a bit of shopping. I installed it in HandlebarCenter, but it was mounted only diagonally. But as Combinat...
I use it for ZX-12R using Pipe Handlebar. Standard Equipment's Wire type lock was very hard to use and I did not use it, so I bought this item.Installation is easy and is completed if it is 10 min...
Attaching a Side case holder etc. to SEROW and its brothers may interfere with existing Helmet holders and be unusable in some cases, but it is useful for such cases.High texture and beautiful appeara...
【What made you decide the purchase?】The fact that there were many VTR attachment articles of this product and Cost performance.Because the Mounting Bolt becomes inside of the hook when Helmet is fixed...
 | ||
| |
These simple custom parts are inconspicuous, but they make you feel different from others by installing them. It is easy to install because you only have to replace it with NORMAL parts.
What made you decide to buy?NORMAL was not so coolHow was your experience with it?The feeling of use is no different from NORMALWas it difficult to install?It's easy to replace with NORMAL, so anyone ...
OEMHookMount is made of iron Simple It's too simple and it does not seem like it's sexy.PMC's Rear suspensionMountHook emphasizes Design property there, Hook part Aluminum, Screw part enha...
OEM's Rear Suspension Mount Hook was a long time feeling on my own.This PMC's Rear Suspension Mount Hook is short and made sharp and Silhouette is satisfied with Refreshing.I chose Black for M...
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
?
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
About our "Mybike" service 
![PMC(Performance Motorcycle Creative) [Carbon Graphite Gasket Series] Dynamo Cover Gasket](http://img-webike-370429.c.cdn77.org/catalogue/images/32218/163-302_01_TS.jpg)
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING